1- 1 gal Latex ROOFING Bonding Glue Adhesive

$71.37 Buy It Now or Best Offer
free,30-Day Returns

Seller Store lottesroofing
(1253) 85.7%,

Location: Saint Charles, Missouri
Ships to: US,
Item: 110737924175

Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money Back
Country/Region of Manufacture:United States
Subject Area:building materials
lottes:lottes

Lottes Roofing St. Charles, MO 63303 We will work with you to give you the best deal on your EPDM, TPO, Modified Bitumen, Roof Coatings, Insulation and Roof accessory items!! Call or Email us TODAY!!! “Over 30 years experience in single ply flat roofing products!” Click Below for Certification, Qualification and Reference Data Click Here for Lottes Roofing InformationResidential and RV Division 1-888-666-9157. COMMERCIAL 1-888-895-4465 This 1 – 1 gal pail of Latex bonding adhesive 11 lbs and is Class C-60 The actual can may be white or a different color in lieu of black, but the application instructions are the same as the product is exactly the same regardless of the exterior can color. Not recommended to be used in temperatures lower than 50*. Temperature needs to be above 50* for 24 hours for full cure. FREE DELIVERY IN 48 states!! Please provide your shipping address, city, state and zip code Check out my other items! 200 page Specification & Installation guideline online manual available at Lottes Roofing Specs Page This is latex bonding adhesive to adhere the EPDM or TPO rubber to the roofing insulation or substrate. This is a BONDING Adhesive to adhere or bond the EPDM or TPO to a substrate of wood, plywood, OSB or metal. This is NOT a seaming product that will seam EPDM to EPDM or TPO to TPO, you must use a SEAMING product like black seaming adhesive or vulcanizing seaming tape which we have available for that type of application. This is a latex based single surface bonding adhesive. This adhesive is a SINGLE surface laminate adhesive that is to be used NOT WET but Tacky condition. DO NOT ALLOW the adhesive to become dry before you lay in the roofing membrane. APPLY roofing membrane while the adhesive is NOT DRY BUT TACKY. So 1 – 1 gal pail will cover about 60-100 square feet of finished roof area. Trowel application is the recommended application as per the instructions as a ONE surface WET LAMINATE. However, if you wish to use a paint roller, we recommend using a 9″ fine nap paint approved roller. If you use the roller, and not a trowel, you need to put the adhesive on BOTH surfaces and let TACK dry for 5 minutes or so, like a 2 sided solvent contact adhesive, depending on weather and heat conditions. Using this application method may require the use of more adhesive than the single sided process.Then, put the 2 pieces together. Full cure normally occurs after 24-48 hours. Method of Applying EPDM with heavy bodied latex bonding adhesive and 3” seam tape application as required.· 1 Clean the roof surface of all shingle debris and nails. Re-fasten any loose roof boards.· 2 Fill any gaps larger than 3/8” inch with wooden strips. The EPDM cannot span gaps of more than 3/8″ without risk of possible adhesion issues.· 3 Start at the bottom of the roof and roll out the EPDM from one side of the roof to the other and let it sit for 10-15 minutes. Fold bottom half of the membrane onto the top half of the in place membrane· 4 Apply the bonding adhesive to the exposed roof deck and NOT to the EPDM membrane as the adhesive is to be applied as a one surface WET LAMINATE using a notched trowel to spread the adhesive in a pattern over the decking. Allow the adhesive a few minutes to “tack off” Slowly fold the EPDM roofing membrane back into place while the adhesive is still wet. To ensure adhesive transfer and a good bond, use a stiff bristled push broom and force the membrane into contact with the adhesive on the roof deck. Repeat the process on the other half of the EPDM membrane.· 5 Roll out the next piece of membrane, allowing a four to six inch overlap on the piece below it. This overlap is crucial to allow enough overlap between the two pieces and to allow the water to flow from the upper part of the roof down to the roof edge. This is also to allow enough room to apply the primer and 3”seam tape if required to splice 2 pieces of EPDM deck sheet together.· 6 Adhere this section in the same manner as the first section. Continue adding sections until you have covered your roof.Seam tape application if required to join 2 sheets together•Position sheets of liner and align edges to required overlap. Mark bottom sheet to indicate top sheet location, then folding back top sheet. •Clean and/or prime the seam area of both rubber sheets using FastSeam EPDM Liner Primer. CAUTION: wear protective gloves and read all labels and instructions when using EPDM Liner Primer or unleaded gas to clean and prime the seam area•Make guide marks for the splice tape much as in Step 1, except that the new marks will be 1/2″ out from the edges of the bottom sheet. •Fold back top sheet. Begin unrolling splice tape by aligning the edge of the paper with the marks in step 3. Continue along the full length of the seam. •With the paper backing still attached to the tape, use a roller to ensure good contact. Place the top sheet of rubber back over the applied tape. •Remove the paper backing by pulling out from under the top sheet at a 45ºangle. Allow top sheet to fall freely onto exposed splice tape. Roll entire seam with roller. We have both WHITE TPO rubber and BLACK EPDM rubber roofing. INSTALLATION OF EPDM MEMBRANE RPU BONDING ADHESIVE The EPDM or TPO membrane may be installed in a fully adhered application directly over 1/2″ or larger plywood decking, APPROVED DECKING OR APPROVED INSULATION, if the deck support is considered adequate for the roof load as determined by the local installer, and the roof installation meets local building codes. Position the EPDM or TPO membrane over the substrate, wood decking, concrete, or insulation, without stretching the sheet. Allow sufficient materials for perimeter attachment. When the new membrane is to be sealed to an abutting membrane, overlap the edge of the new membrane 5” onto the “in place” membrane. Bond the new sheet to the substrate by folding the sheet lengthwise on to itself so that one half of the underside is exposed. Smooth out all the wrinkles and buckles along the folded edge. Apply the bonding adhesive evenly at the rate of 70 -100 sq. ft. per gallon per receiving surface using a 9″ plastic core paint core paint roller or application trowell with 1/8″ x 1/8″ groove indents. Apply the roofing menbrane onto the wet adhesive while still wet to insure “transfer” of adhesive to underside or roofing membrane. Roll or lay the membrane onto the substrate taking care to avoid wrinkling. Bond the adhered half of the membrane with a 18″ to 24″ heavy duty push broom using a pushing motion to achieve maximum contact. Pull back the unbonded half of the sheet and repeat this procedure. Do not apply adhesive to the top surface of any abutting membrane that is to be used as the seam joint. Summary of My Selling Policies Payment All Credit Cards, Company Certified Checks, Bank Checks, Money Orders, Bank Wire, Paypal Fees No sales taxes UNLESS in specific states locals Shipping US and International Delivery 24-48 hours to ship the liner NORMALLY on in stock items, not counting weekends or holidays Refunds & Returns Returns accepted on qualified items with RGA return number Contact Me Residential and RV Division 1-888-666-9157. COMMERCIAL 1-888-895-4465 BID WITH CONFIDENCE Read my policies on my SquareTrade Seal stwithpolicies On Apr-28-08 at 11:12:31 PDT, seller added the following information: Please be prepared to unload the product from the delivery vehicle. Items less than 150 lbs will be shipped UPS or Fed Ex and will deliver directly to your door. Orders over 150 lbs delivered by Trucking Companies DO NOT DO DOOR delivery for residential delivery. It is the responsibility of the CUSTOMER to remove his product FROM or OFF the actual truck. We do NOT offer a lift gate option, that would be an expense item negotiated between the Freight Company and the customer/consignee. If you are unable or unwilling to receive your order via normal delivery according to ICC policies and truck line delivery schedules, then you will be solely responsible for all delivery charges related to attempted delivery and return freight charges. A 15% restocking fee will apply to returned items.

Frequently Asked Questions About 1- 1 gal Latex ROOFING Bonding Glue Adhesive in My Website

24hournewsupdates.com is the best online shopping platform where you can buy 1- 1 gal Latex ROOFING Bonding Glue Adhesive from renowned brand(s). 24hournewsupdates.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling 1- 1 gal Latex ROOFING Bonding Glue Adhesive on 24hournewsupdates.com?

1- 1 gal Latex ROOFING Bonding Glue Adhesive

Frequently Asked Questions About 1- 1 gal Latex ROOFING Bonding Glue Adhesive in My Website

What are the best-selling 1- 1 gal Latex ROOFING Bonding Glue Adhesive on 24hournewsupdates.com?

No Responses

Leave a Reply Cancel reply