2001-2003 Suzuki RM125 Pryme Engine Cover & Frame Guard Pack Grip Tape RM 125

$40.0 Buy It Now or Best Offer
free,30-Day Returns

Seller Store prymemx
(8326) 99%,

Location: Spokane, Washington
Ships to: US,
Item: 204507821614

Restocking Fee:No
Return shipping will be paid by:Buyer
Returns Accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money Back
Pryme:Pryme
Manufacturer Part Number:SBC4, SBi3, SBF1

Fits2001-2003 Suzuki RM125Includes -Right and Left Frame Guards -Clutch Cover Guard -Ignition Cover Guard (see our other listings to purchase these separately)What Do They Do?Protects the coating or metal on your frame and engine coversAdds gripCovers up worn looking frames and engine coversGives your bike a clean lookWhat Are They?These are thick vinyl protectors that have a very strong adhesive backing. They apply easily but don’t add bulk to your frame or engine covers. These are not made from sandpaper type material, so they will not wear down your boots and riding gear.This pack includes guards for clutch cover, ignition/flywheel cover, and both sides of frame.Keep in mind, these guards do not last forever. The lifetime of them depends on the care taken while installing, as well as your riding style. Protecting your engine covers with guards is much cheaper and easier than refinishing your covers every few months due to wear and tear on the coatings/metal.Image may not be an exact representation of the guards for your model, but you will receive the correct guards for your bike.SpecsMade from 0.7mm thick vinylExtreme high adhesion allows guards to stay in placeTextured finish provides grip between rider and bikePerfect fit ensures edges do not peel up prematurelyAll black design with model of bike (on engine guards) and Pryme logo printed into guardFeatures a corner guard, which prevents peeling in high wear areasAdheres to aluminum, steel, plastic, powder coat, and cerakote100% made in the USA!Some engine guards may have a cutout around raised lettering, such as on CR125 models. These only fit on stock engine covers.Why buy from Pryme?We stock every part in house, and it’s ready to ship today. No backorders, no drop shipping, and no hassle. We’re riders too and we understand how important it is to receive orders in a timely and accurate manner. Pryme is 100% American owned and employs hard working Americans.How To InstallGetting StartedHave a heat gun or hair dryer on hand.Do not use any type of water, windex, or soap solution while installing guards.Install guards in a warm area to help them adhere and conform better.Guard InstallationRemove any glue, dirt, or grease from frame or cover.Clean surface with isopropyl alcohol or contact cleaner, and let dry.Use a heat gun or hair dryer to warm up the surface and guard if temperature is below 60F.Peel part of the paper backing away, and line up guard at the most detailed part.Be sure not to touch the part surface or adhesive with your bare hands.Once you are happy with the alignment, tack the guard down at the center and work your way from the center towards the edges.If the guard is off center or an air bubble starts to form, you can carefully peel up the guard to correct.As you get to the edges and tighter spots, creases may start to form. Add a small amount of heat to stretch the guard so it lays flat.Do not apply excessive heat, as this may melt the guard.If your cover or frame has tight crevices, use a soft rubber or plastic edge to help press the guard into those spots.Once the guard is fully tacked in place, heat the guard again while applying pressure. This is very important to the adhesion of the guard, so make sure you don’t skip this step.Getting The Most Out Of Your GuardsWhen installing the guard, make 100% sure the surface is clean and the edges are not hanging off the part.It is not recommended to use boots with steel toe caps, as this will wear out guards much quicker.If you notice an edge start to peel up, apply heat and tack it back down or lightly trim the edge.If using a pressure washer to clean your bike, take caution around the guards.Removing Old GuardsBefore removing a worn guard, apply heat to help soften up the adhesive, this will also prevent adhesive from being left behind.If adhesive is left afterwards, tack the old guard over the adhesive and this will help peel it up. Use a contact cleaner or isopropyl alcohol to remove any leftover adhesive. Easiest Way To Transform Your Bike! Video will open in a new window Using the eBay App? Paste link into a browser window: [isdntekvideo]

Frequently Asked Questions About 2001-2003 Suzuki RM125 Pryme Engine Cover & Frame Guard Pack Grip Tape RM 125 in My Website

24hournewsupdates.com is the best online shopping platform where you can buy 2001-2003 Suzuki RM125 Pryme Engine Cover & Frame Guard Pack Grip Tape RM 125 from renowned brand(s). 24hournewsupdates.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling 2001-2003 Suzuki RM125 Pryme Engine Cover & Frame Guard Pack Grip Tape RM 125 on 24hournewsupdates.com?

2001-2003 Suzuki RM125 Pryme Engine Cover & Frame Guard Pack Grip Tape RM 125

Frequently Asked Questions About 2001-2003 Suzuki RM125 Pryme Engine Cover & Frame Guard Pack Grip Tape RM 125 in My Website

What are the best-selling 2001-2003 Suzuki RM125 Pryme Engine Cover & Frame Guard Pack Grip Tape RM 125 on 24hournewsupdates.com?

No Responses

Leave a Reply Cancel reply